When one stops to ponder the relationship of stylus to groove, the numbers boggle the mind. Groove width on a vinyl LP ranges from .001″ – .0014″ (.025mm – .035mm). Contrast that with a human hair which measures .006″ – .007″ (.17mm – .181mm) and it’s amazing that vinyl reproduction works at all, much less as well as it does. With those numbers in mind, you quickly realize how critical cartridge alignment becomes. The relationship of stylus to groove is incredibly minute, requiring precise alignment, with no room for error. Furthermore, poor alignment can lead to asymmetrical record wear. The stylus exerts tremendous forces on the groove walls. Though a tracking force of 1.5 grams seems rather insignificant, when translated to the small contact area of the stylus, we’re looking at about 340 pounds per square inch!
Now that you’re afraid to go near your cartridge, be heartened, it’s not as difficult as you might think. With the help of a few simple tools and equipped with some basic knowledge, you can fine tune your analog rig for optimum performance. Let’s take a look at the areas of adjustment.
Vertical Tracking Force (VTF): Setting tracking force is the very first step in setting up a cartridge (though it will be repeated later to fine tune). The cartridge manufacturer recommends a range (e.g. 1.75g – 2.0g) that is appropriate for their design. Too little tracking force and the stylus will not seat properly in the groove, too much tracking force and you’ll overload the internal suspension, resulting in a loss of performance. Interestingly, too little tracking is more likely to increase wear than a high setting.
More than just applying force to seat the stylus in the groove, the correct tracking force aligns the internal generator assembly. For a finely tuned rig, it is important to experiment within the manufacturers recommended range to find the precise point that gives the best sound. The amount of difference between the different settings within the range may be significant or negligible depending on the cartridge brand/model and the resolution of the system to reveal the changes.
There are a number of options when it comes to tracking force calibration, which one is best will be determined by the quality of the system involved. A quick adjustment using graduations on the arm or an inexpensive balance beam scale is adequate for modest systems, but is not accurate enough for a high end turntable set up. At that level we strongly recommend the use of a digital stylus force gauge.
Our Note: We’ve had great success with the Measure-It from Pro-Ject. $99
Overhang: As the stylus tracks across the record, it is important that the stylus remain tangent to the groove. Setting overhang we are aligning the cartridge to follow that ideal arc across the record. In a radial tracking tonearm, there are only a couple of points when it actually is (null points). Without getting overly bogged down in technicalities, there are at least a couple of theories about where the null points should be, and so some gauges are slightly different than others depending on which the manufacturer thinks is best.
To set overhang, you’ll need an alignment gauge. There are a number of overhang gauges available through the years (DB Systems, Denessen Soundtractor, Mobile Fidelity Geodisc, to name a few). People usually like the one they’ve used before, but even the simple template
provided with your turntable or tonearm are useable.
Our Note: Probably the best alignment protractor that’s ever been devised is the Feickert Alignment System. Precise alignment is critical and the Feickert is the best.
VTA or SRA: VTA is an abbreviation for vertical tracking angle, SRA stands for stylus rake angle.The two terms (while not exactly the same) are generally used interchangeably to describe the relative angle of the stylus to the groove. (Though I’d say SRA is the more accurate term, most audiophiles are more familiar with VTA, so I’ll stick with it here). This angle is normally adjusted by raising or lowering the back of the tonearm (although shims can be used between the headshell and cartridge). Neutral VTA is achieved when the tonearm is parallel to the record surface (although with some arms it may be more convenient to use the top of the cartridge body as the reference point). As the back of the tonearm is lowered (so that the cartridge body tips rearward), VTA becomes negative. Conversely, raising the arm creates a positive VTA.
Correct VTA is achieved when the angle of the playback stylus matches that of the cutting stylus used to make the original master lacquer. Because the angle of the record lathe cutter head (normally specified as twenty degrees, plus or minus five degrees) varies to some degree from manufacturer to manufacturer, we must adjust our VTA to achieve optimum playback results. Other variables such as record thickness, stylus shape and variations in cartridge construction, also make VTA adjustment necessary.
Proper VTA will be achieved by trial and error through listening tests. One should start with a neutral VTA condition as described above, then proceed in small increments up and down, until the best setting is achieved. As a rule of thumb, most cartridges that I have set-up prefer a slightly negative VTA. That is to say, the back of the cartridge body is slightly closer to the record surface than the front. In looking for the “sweet-spot,” there are several things to listen for. Look for the point at which the soundstage comes into best focus, providing maximum width and depth simultaneously. Additionally surface noise is at a minimum and harmonics are well balanced. You will find (to a varying degree depending on the cartridge) a shift in tonality. Usually a positive VTA results in an emphasized top-end, while lowering the setting toward negative will soften the high-end and increase the bass. Due to stylus shape and size, some cartridges will be more sensitive to VTA than others. Generally, the more radical the stylus cut, the more sensitive to proper adjustment of VTA. All cartridges however, will benefit, at least to a degree, from proper VTA alignment.
It is important to note that vertical tracking force (VTF) is directly related to VTA. As tracking force is increased cantilever deflection increases, changing the relationship of stylus to groove. So fine tune VTF before zeroing in on VTA.
Azimuth: Even more critical (in my opinion) to proper set-up than VTA, is cartridge azimuth. Unfortunately VTA gets all the press, therefore many people are not aware of the importance of this adjustment. What is azimuth? Looking at the cartridge body from the front, it is the left to right tilt of the cartridge body. Contrary to popular belief, azimuth is not necessarily correct with the sides of the cartridge body are perpendicular to the record surface. What we’re actually looking for is the correct relationship of the stylus to the groove. Unfortunately, the vast majority of styli are not mounted perpendicular to the bottom of the cartridge body, thus making azimuth set-up by sight alone erroneous. And with the current trend toward decreasing stylus size, even seeing the stylus without the aid of magnification borders on the improbable. The “eyeball” or “mirror” method should only be employed if other more sophisticated methods are unavailable.
The gold standard for determining the correct azimuth is a dedicated cartridge analyzer or Fosgate Fozgometer from Musical Surroundings (see below). A test tone (typically 1kHz) is played on one channel while the analyzer looks at the output from the opposite channel. This crosstalk is a measure of cartridge separation. When the crosstalk is at its lowest, and equal on both channels, the azimuth is optimized. If you can obtain a test record, an oscilloscope or accurate digital voltmeter can be substituted for the dedicated cartridge analyzer mentioned above.
Lacking the test equipment previously described, other less sophisticated methods may be employed to set azimuth. The simplest alternative, connect one channel of the cartridge out of phase with the other (simply reverse the + and – on one channel only) and play a test record with a mono track or a monophonic record (preferably one with simple instrumentation). Out of phase information cancels so adjust azimuth by tuning for least output.
From Harry Weisfeld at VPI comes yet another rather simple method, requiring only a mono record and a pair of ears. He suggests that a simple mono recording of voice should provide a stable, non-wavering image, precisely centered between the two
speakers. Adjust the azimuth to achieve optimum results. This method works well if you’re practiced enough to know what to listen for, though most listeners would be better served by using one of the tests outlined previously. Best option, use the Fozgometer.
We recommend using the Fozgometer to correctly set Azimuth.
From a mechanical standpoint, adjusting azimuth on some tonearms may be difficult. Some manufacturers (e.g. SME, Rega), in their unbending quest for maximum rigidity, have eliminated azimuth adjustments altogether. In most cases, this doesn’t mean that you are stuck with an improperly aligned cartridge, but it does mean that your task is a bit more formidable. Arms lacking these adjustments must be shimmed at the base (or the cartridge adjusted with washers) to achieve accurate azimuth. It’s a pain, but worth the effort.
Note: The SME IV, IV-Vi and V do not have dedicated azimuth adjustments, but their azimuth can be changed. Simply loosen the two base locking screws and, by firmly grasping the bearing housing at the back of the tonearm, you can shift the arm left-right a few degrees. While this is not a wide range of adjustment, it will be enough to correct for any minor cartridge deficiencies. Re-tightening the base locking screws will lock in the adjustments. REGA tonearms do not have adjustable VTA.
Zenith: Aligning the stylus with in the groove in the horizontal plane dials in zenith. Looking down on the cartridge from above, zenith is changed by rotating the cartridge (as if around a clock face). Of course there is only a very small amount of adjustment possible on most arms, just the play in the mounting screws.
Zenith is best adjusted using test equipment, but one can (assuming the stylus is correctly mounted to the cantilever) also adjust by eye using an overhang gauge with an alignment grid. Simply sight down the cantilever from the front, aligning it with the line directly below it on the gauge.
Anti Skate Bias: Tonearm geometry creates a force that pulls the cartridge toward the center of the record. Anti skate bias counteracts that force, seeking to equalize pressure of the stylus on both sides of the grooves. Just how to set anti skate is somewhat of a controversy.
Most all tonearms will have calibrated, adjustable anti skating. The normal practice would be to dial in anti skating to match the tracking force. (i.e. 2g of tracking force and 2g of anti skating bias). However, higher compliance cartridges are more affected by anti skating adjustment than low compliance cartridges, so some manufacturers suggest setting anti skating for low compliance cartridge at about one-half to two-thirds the tracking force, high compliance
Some suggest using a grooveless record. but Sumiko disagrees stressing that skating is a dynamic force and using a blank or grooveless disc will result in over compensation.
Another method suggests lowering the stylus into the groove while watching from the front to see if the cartridge has a tendency to move inward or outward, then adjusting anti skate until there is no perceived motion.
It would be difficult to overstress the importance of proper cartridge alignment. If you expect to get all the performance promised by your costly investment in analog, these adjustments simply must be made. So please take the time to insure that your arm/cartridge combination is properly set-up. The number of dealers with a good analog background is small. Hopefully you have a good one in your area. If not it pays to learn the ropes yourself to insure be sure that it has been done correctly. Your investment in time will pay off with the reward of better sound. Note: More information on cartridge set-up is available in our article Turntable Set-Up.
http://www.gcaudio.com/resources/howtos/cartbasics.html